Beginners Guide to Keyboard Modification

If you’ve ever had a problem with your keycaps shifting and vibrating while you type, you know how annoying it is. As a general rule, everyone wants keys that feel solid and stable when typing on them. If you’re looking for a way to make your mechanical keyboard keys more stable, the best option is to modify the stabilizer.

Before modifying the keyboard stabilizer, you should be aware of the five most common mistakes people make. Let’s take a closer look at how this works. Stabilizers: How to Modify Them Your mechanical keyboard’s stabilizer can be improved with Band-Aids, Clips, and Lubricant. If you are interested, read more guides on helveticaforever.com.

Mechanical keyboard stabilizers

The larger keys, such as Space, Left Shift and Right Shift, Enter, and Capslock, are balanced using a stabilizer on a mechanical keyboard. Mechanical keyboards with plastic plates benefit greatly from stabilizers because they not only balance out large keys, but they also shield the plate from damage when keycaps hit it directly.

As a result of the stabilization of the mechanical keyboard, typing will be more comfortable because the keys will no longer vibrate or sway as a result of the stabilizer. As a result, the stabilizer is one of the mechanical keyboard’s (optional) components that must be used.

What are the benefits of customizing your mechanical keyboard stabilizers?

Improved key balance is one of the primary goals of altering the stabilizer on a mechanical keyboard. It’s much cheaper to modify the stabilizer than it is to change the keycaps, but it has a huge impact on the mechanical keyboard.

Stabilizing the mechanical keyboard’s buttons improves their strength and balance, reduces vibration on the buttons, prevents them from slamming into a PCB protective plate, and reduces the mechanical keyboard’s sound.

Modifying mechanical keyboard stabilizers requires certain tools

When it comes to modifying your mechanical keyboard’s stabilizer, you’ll need a few essential tools on hand. You don’t need to spend a lot of money on the tools you’ll need. A soldering iron isn’t necessary to open the switch on a Hot Swappable mechanical keyboard.

Do this on a dedicated workbench, not on a cluttered and dirty workstation. Tools for modifying the mechanical keyboard stabilizer are as follows:

  • To remove the keycaps from the switch, use a keycap puller.
  • To remove the switch from the PCB, use a switch puller.
  • A tool for soldering and removing solder from electrical switches (For Standard PCB)
  • Band-Aid: Used to cover the stabilizer on the PCB with a thin layer of coating.
  • Scissors: used for slicing various parts.
  • Tool for installing and removing screws
  • Tiny objects can be handled with tweezers.
  • The lubrication of stabilizers with dielectric grease
  • To apply lubricant to the stabilizer, use a small brush.

Modding requires preparation of the keyboard

We’ll be modifying the stabilizer on a mechanical keyboard, so get it ready! To get ready, remove your mechanical keyboard’s keycaps, switches, and stabilizers from the PCB.

1. Remove the keycaps first

Open the keycaps without stabilizer first when disassembling a keyboard. Removed or sorted keycaps can be placed on your desk in the same way as installed keycaps. It’s best to use the aluminum keycaps puller if you have to open the caps with your fingers otherwise you’ll damage the keycaps.

2. Unplug the switch from the board

The keyboard’s mechanical PCB should be cleared of any switches with stabilizers. By doing this, you’ll save time. Especially if your keyboard is not Hot Swapable, the soldering job is going to be a lot more difficult. In order to replace the switch on a hot swappable mechanical keyboard, you simply use a switch puller.

3. Stabilizer must be removed from PCB

In order to release the stabilizer, press the small lever located on the stabilizer (this is for the stabilizer mounted on the plate). You must use a screwdriver to remove the stabilizer’s screw while it is attached to the PCB.

Mechanical keyboard stabilizer band-aid modification

This is how you apply a band-aid to a mechanical keyboard PCB so that the stabilizer can use it. When the stabilizer is working, this is intended to reduce noise and protect the PCB from damage. Band-Aids can be used as stabilizers as long as they’ve been cut to fit around them and Dielectric grease has been applied to the band-aid.

1. Remove band-aids with the stabilizer holder’s

Cut the band-aid into 6x3mm pieces. Band-aids of the same size are needed for each stabilizer piece.

2.Fix the PCB with band-aids

The band-aid should be placed on the PCB just below the stabilizer. Before you attach the stabilizer, make sure the band-aid is firmly attached to the PCB.
Put a dab of Dielectric grease on the band-aid that has been successfully attached to the PCB, and then place the stabilizer directly on top of that.

The stabilizer’s clip modification

Avoid damaging your stabilizer by cutting the stabilizer incorrectly when performing Mod Clip Stabilizer. The stabilizer insert’s bottom only needs to be removed.

1. The stabilizers must Be removed first

Begin by removing the stabilizer from its packaging.
Remove the stabilizer components from the housing and remove the metal rods from the stabilizer clamps on the left and right.

2. Remove and replace the stabilizer insert

The next step is to exercise extreme caution when chopping the stabilizer. The bottom-mounted stabilizer mounts have a rectangular section that will be cut on both sides. The inserts on both sides of the stabilizer mount are all that is required to be cut.
Reassemble the stabilizer’s components into the housing after you’ve cut them out according to our directions. On the stabilizer, you’ve finished modifying the Clip!

Modification of the stabilizer lube

A lubricant can be applied to stabilizer components in order to reduce friction between them. Additionally, the stabilizer’s components will be better protected, resulting in longer-term use.
Stabilizer movement will be smoother as well as the stabilizer components will be treated. Lubricate the moving parts, such as the mounting metal rods and the stabilizer housing, by spraying some silicone grease on them. To apply the lubricant, a small brush works well.

1. Lube the metal rods

The metal stabilizer rod that will be inserted into the stabilizer housing should be oiled. In order to keep the stabilizer housing from rusting, you don’t need to add any lubricant. The PCB and mechanical plate of your keyboard don’t need to be covered in lubricant, so just a thin layer will do.
Stabilizer metal rods should be lubricated on both sides as shown below.

2. Reinstall the stabilizer components in their original locations

Reinstall the lubricated iron stabilizer rod.
It is time to put the stabilizers back into place on the PCB. Those three methods can be applied to all of your mechanical keyboard stabilizers simultaneously.
As soon as you’ve reinstalled all the components you’ve opened, take advantage of the improved feel of your mechanical keyboard’s switches and keycaps.

What are the best ways to modify your stabilizer?

Clip and Lube are the best keyboard stabilizer modifications. When it comes to eliminating rattle, vibration, dampening sound and adjusting the balance buttons, both of these methods make significant improvements to the stabilizer. The stabilizer’s best modification is the Clip and Lube.

Because the band-aid modification is optional, but it’s also a good idea, it can reduce the sound of typing and dampen vibrations on the keyboard. Protecting the PCB’s surface from a hard-pressed stabilizer can also be done with Band-Aid.

Conclusion

A mechanical keyboard stabilizer modified in three different ways is the most effective method for enhancing the stability of the keys.
Because each modification method serves a different purpose, you can also use one of these methods. The stabilizer will be attached to the PCB surface and band-aids will be used to muffle the sound of the keyboard being typed on.
To reduce the impact of plastic on the stabilizer housing, clip modification is a stabilization modification. Therefore, the rectangle is cut on both sides.
In order to make the stabilizer more slippery and smooth, we’ll lubricate the metal rod mounted on the stabilizer housing. Lubrication changes on the stabilizer are also necessary to prevent metal rods from rubbing against the stabilizer housing, which can lead to corrosion and damage.